![background image](http://html.mh-extra.com/html/lg/lre3163-series/lre3163-series_owners-manual_218318037.webp)
37
MAINTENANCE
ENGLISH
6
Close the oven door.
Press
EasyClean
®
.
Press
Start
.
CAUTION
•
Some surfaces may be hot after the
EasyClean® cycle. Wear rubber gloves while
cleaning to prevent burns.
•
During the EasyClean® cycle, the oven
becomes hot enough to cause burns. Wait until
the cycle is over before wiping the inside surface
of the oven. Failure to do so may result in burns.
•
Avoid leaning or resting on the oven door glass
while cleaning the oven cavity.
7
A tone will sound at the end of the 20 minute
cycle. Press
Clear/Off
to clear the display and
end the tone.
8
After the cleaning cycle and during hand-
cleaning, enough water should remain on the
oven bottom to completely submerge all soils.
Add water if necessary. Place a towel on the
floor in front of the oven to capture any water
that may spill out during hand-cleaning.
9
Clean the oven cavity immediately after the
EasyClean
®
cycle by scrubbing with a wet,
non-scratch scouring sponge or
pad. (The scouring side will not
scratch the finish.)
NOTE
Do not use any steel scouring pads, abrasive
pads or cleaners as these materials can
permanently damage the oven surface.
10
Once the oven cavity is cleaned, wipe any
excess water with a clean dry towel. Replace
racks and any other accessories.
11
If some light soils remain, repeat the above
steps, making sure to thoroughly soak the
soiled areas.
NOTE
•
If you forget to saturate the inside of the oven with
water before starting EasyClean
®
, press
Clear/Off
to end the cycle. Wait for the range to cool to room
temperature and then spray or pour water into the
oven and start another EasyClean
®
cycle.
•
The cavity gasket may be wet when the
EasyClean
®
cycle finishes. This is normal. Do not
clean the gasket.
•
If mineral deposits remain on the oven bottom after
cleaning, use a cloth or sponge soaked in vinegar
to remove them.
•
It is normal for the fan to operate during the
EasyClean
®
cycle.
Cleaning the Exterior
Painted and Decorative Trim
For general cleaning, use a cloth with hot soapy
water. For more difficult soils and built-up grease,
apply a liquid detergent directly onto the soil. Leave it
on for 30 to 60 minutes. Rinse with a damp cloth and
dry. Do not use abrasive cleaners.
Stainless Steel Surfaces
To avoid scratches, do not use steel wool pads.
1
Place a small amount of stainless steel
appliance cleaner or polish on a damp cloth or
paper towel.
2
Clean a small area, rubbing with the grain of the
stainless steel if applicable.
3
Dry and buff with a clean, dry paper towel or soft
cloth.
4
Repeat as necessary.
NOTE
To prevent scratching, do not use abrasive
cleaners on any of these materials.
NOTE
•
Do not use a steel wool pad. it will scratch the
surface.
•
To clean the stainless steel surface, use warm
sudsy water or a stainless steel cleaner or
polish.
•
Always wipe in the direction of the metal
surface finish.
•
To purchase stainless steel appliance cleaner
or polish, or to locate a dealer near you, call our
toll-free customer service number or visit our
website at: www.lg.com
Summary of Contents for LRE3163 Series
Page 93: ...47 Memo Español Memo ...
Page 94: ...48 Memo Memo ...
Page 95: ...49 Memo Español Memo ...
Page 96: ...Printed in Mexico ...