manualshive.com logo in svg

LG LDF7774BB, Service Manual

Share
Download
LG LDF7774BB Service Manual Download Page 31

For Authorized Service Technician

For Authorized Service Technician

- 31 -

Excess Error

Condition.

Excessive water is supplied than normal water

level. (Automatically drain Pump operated.)

Yes

Yes

Yes

No

No

No

No

Is the water supplied when

the machine is shut down?

Is the connector connected to 

main PCB assembly disconnected 

or disassembled? (NA8)

Is the voltage between connectors 

out of range? (NA8 pin1 ~ pin2)

 - After remove terminal position 

assurance (TPA) of connector, 

check the voltage when water is 

injected.

(The voltage is 2.5V AC (±15%)

Is the resistance vales between 

connectors out of range? 

(range is over 5MΩ)

(White 8P, Pin1~Pin2)

Does the inlet valve

working properly?

(damaged or operating

abnormally)

Replace the inlet valve

Reconnect or 

repair the connector.

Replace the main 

PCB assembly

Is the Inlet sensor operate properly?

(red+black range is 8~10kΩ)

Replace the inlet valve

(white+black range is 15~30MΩ)

Yes

(Close the water tap.)

Is       displayed?

Summary of Contents for LDF7774BB





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands