manualshive.com logo in svg

LG LDF7774BB, Service Manual

Share
Download
LG LDF7774BB Service Manual Download Page 29

For Authorized Service Technician

For Authorized Service Technician

- 29 -

Drain Error

Condition.

Not fully drained out in spite of 5 min. 

drain operation.

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

No

No

No

No

No

Motor rpm is not increased.

Motor rpm is 

increased.

Does the drain motor operate?

Check the rpm of drain motor by the 

test Mode.

Is the connector connected to 

main PCB assembly disconnected 

or disassembled? (YL3)

Is the voltage between connectors

out of range? (YL3 pin1~pin2~pin3)

 - After remove terminal position 

assurance (TPA) of connector, 

check the voltage when water is 

drained. (The voltage is over 12V DC)

Is the resistance vales between 

connectors out of range? 

(range is 4~5Ω)

(Yellow 3P, pin1~pin2~pin3)

Is the connector connected to 

drain motor disconnected 

or disassembled?

Reconnect or 

repair the connector.

Replace the main

PCB assembly.

Replace the drain

motor

Reconnect or 

repair the connector.

Is the filter clogged?

Clean the filter

Remove the cause of kink

or block.

Remove the cause of kink

or block.

Is the outer drain hose

kinked or blocked or frozen?

Is the inner drain hose

and drain case

kinked or blocked or frozen?

Is       displayed?

Summary of Contents for LDF7774BB





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands