background image

- 51 -

LGE Internal Use Only

Copyright © 2007 LG Electronics. Inc.  All right reserved. 
Only for training and service purposes

3.3. Audio Part

3.3.1 Audio Part Block Diagram

3.3.2 Audio Signal Processing & Interface

Audio signal processing is divided Uplink path and downlink path.

The uplink path amplifies the audio signal from MIC and converts this analog signal to digital signal

and then transmit it to DBB Chip (Asta).

This transmitted signal is reformed to fit in GSM & WCDMA Frame format and delivered to RF Chip.

The downlink path amplifies the signal from DBB chip (Asta) and outputs it to Receiver (or Speaker).

The audio interface consists of PCM encoding and decoding circuitry, microphone amplifiers and

earphone drivers. The PCM encoder and decoder blocks are two-channel, 16-bit circuits with

programmable gain amplifiers (PGA).

The decoder has a receive volume control. The audio inputs and outputs can be switched to normal or

auxiliary ports.

3. Technical Brief

Figure 3-3-1. Audio Part Block Diagram

Summary of Contents for KU580


















































































































































































































Reviews: