manualshive.com logo in svg

LG Hydro Kit ARNH04GK2A4, Installation Manual, Page: 53 / 63

Share
Download
LG Hydro Kit ARNH04GK2A4 Installation Manual Download Page 53

Hydro Kit

Installation Manual 

53

ENGLISH

System Set-Up   

• Tank disinfection setting 1, 2

Disinfection operation is special DHW tank operation mode to kill and to prevent growth of viruses
inside the tank. 

- Disinfection active : Selecting enable or disable of disinfection operation. 

- Start date : Determining the date when the disinfection mode is running. 

- Start time : Determining the time when the disinfection mode is running.

- Max temp. : Target temperature of disinfection mode.

- Duration time : Duration of disinfection mode.

Vales of Tank disinfection setting

• If Disinfection active is set as ’ Not use’, that is ‘disable disinfection mode’, Start date and Start

time is not used.

• When Disinfection active is set as ’Use’, that is ‘enable disinfection mode’, Start date is

displayed at the position of Disinfection active and Start time is displayed at the position of Start
date.

DHW heating should be enable

• If Disinfection active is set as ’ Not use’, that is ‘disable disinfection mode’, Start date and Start

time is not used.

• When Disinfection active is set as ’Use’, that is ‘enable disinfection mode’, Start date is

displayed at the position of Disinfection active and Start time is displayed at the position of Start
date.

NOTICE

NOTICE

Time

Start time

Max temp

Duration time

Water temperature

(Inside DHW)

Temperature profile

of Disinfection operation

Summary of Contents for Hydro Kit ARNH04GK2A4
































































Reviews:

No comments