manualshive.com logo in svg

LG Hydro Kit ARNH04GK2A4, Installation Manual, Page: 33 / 63

Share
Download
LG Hydro Kit ARNH04GK2A4 Installation Manual Download Page 33

Hydro Kit

Installation Manual 

33

ENGLISH

Accessories Installation

General Information

Hydro Kit 

supports following thermostats.

(1) There is no electric circuit inside the thermostat and electric power supply to the thermostat is not

required.

(2) Electric circuit such as display, LED, buzzer, etc is included in the thermostat and electric power

supply is required.

(3) Thermostat generates "Heating ON or Heating OFF" signal according to user"s heating target

temperature.

(4) Thermostat generates both "Heating ON or Heating OFF" and "Cooling ON or Cooling OFF" signal

according to user"s heating and cooling target temperature.

CAUTION: 

Choosing Heating / Cooling Thermostat

• Heating / Cooling Thermostat must have "Mode Selection" feature to distinguish operation

mode.

• Heating / Cooling Thermostat must be able to assign heating target temperature and cooling

target temperature differently.

• If above conditions are not kept, the unit can not operation properly.
• Heating / Cooling Thermostat must send cooling or heating signal immediately when

temperature condition is satisfied. No delay time while sending cooling or heating signal is
permitted.

Type

Power

Operating Mode

Supported

Mechanical 

(1)

1~ 230 V

Heating Only (3)

Yes

Heating / Cooling (4)

Yes

1~ 24 V

Heating Only (3)

Yes

Heating / Cooling (4)

Yes

Electrical 

(2)

1~ 230 V

Heating Only (3)

Yes

Heating / Cooling (4)

Yes

1~ 24 V

Heating Only (3)

Yes

Heating / Cooling (4)

Yes

Summary of Contents for Hydro Kit ARNH04GK2A4
































































Reviews:

No comments