manualshive.com logo in svg

LG Hydro Kit ARNH04GK2A4, Installation Manual, Page: 31 / 63

Share
Download
LG Hydro Kit ARNH04GK2A4 Installation Manual Download Page 31

Hydro Kit

Installation Manual 

31

ENGLISH

Accessories Installation

Water tank temperature sensor Connection

• Select the suitable pump by referring to the flow rate table with water

temperature difference between the entrance and the exit.

• It is recommended that the flow rate is Rated water flow (refer to the

specification of PDB)

• Use the pump with enough capacity to guarantee the loss of entire water

pressure and to supply the 

Hydro Kit

with water. 

• Select a suitable relay for pump capacity when connecting the pump to the

unit.

• Connect the relay to the terminal block 11 and 12 of the control box.

• Connect sensor housing to PCB‘CN-TH4’ connector (red).

11

12

L

N

Pump

(main)

Relay

Pump

Water tank
thermistor

Housing

CN-TH4

CAUTION: 

• Make sure to supply external power with the pump.

CAUTION: 

• If water tank temperature sensor is not connected, error will occur. 

(CH08) Exclude the case of using floor heating.

Main Pump Connection

Summary of Contents for Hydro Kit ARNH04GK2A4
































































Reviews:

No comments