LG GoldStar MA-1302S Service Manual Download Page 8

Page: 8 / 39

OPERATING SEQUENCE

The following is a description of component functions
during oven operation.

1. SETTING THE CLOCK

NOTE: 1) This is a 12 hour clock.

2) Clock will operate as long as power is

applied to the oven.

2. CANCEL FUNCTION

Touch the pad whenever you need to
cancel an entry or a function currently in use.
The display will either return to the last item entered
or to the clock.

3. EZ ON

4. SENSOR TOUCH

5. TIME COOKING

6. SENSOR COOK

7. AUTO COOKING

8. CHILD LOCK

This oven has a CHILD LOCK feature

TO SET CHILD LOCK

¥ Touch the pad
¥ Touch and hold STOP/CLEAR pad

LOCKED

appear on the display.

TO CANCEL CHILD LOCK
¥ Touch the pad
¥ Touch and hold STOP/CLEAR pad

LOCKED

disappears.

9. MORE / LESS

The cook time is adjustable by MORE pad or LESS
pad

10. TIMER

11. SENSOR POPCORN

12. SENSOR BEVERAGE / REHEAT

/ DEFROST

4-2

STOP/CLEAR

TIMER

For 3 seconds

Time setting

once

STOP/CLEAR

REHEAT

STOP/CLEAR

DEFROST

STOP/CLEAR

EZ on

STOP/CLEAR

COOKING

STOP/CLEAR

POPCORN

STOP/CLEAR

BEVERAGE

STOP/CLEAR

SENSOR REHEAT

STOP/CLEAR

SENSOR DEFROST

STOP/CLEAR

COOKING

LESS

STOP/CLEAR

POWER

START

STOP/CLEAR

START

STOP/CLEAR

START

EZ ON

STOP/CLEAR

TIMER

START

START

EZ ON

STOP/CLEAR

AUTO

COOK

START

START

EZ ON

START

START

EZ ON

START

EZ ON

START

EZ ON

START

EZ ON

Push

START

EZ ON

Minute setting

START

EZ ON

START

Summary of Contents for GoldStar MA-1302S








































Search results

Summary of Contents for GoldStar MA-1302S

Reviews:

LG GoldStar MA-1302S, Service Manual, Page: 8 / 39

Search results

Summary of Contents for GoldStar MA-1302S

Reviews: