LG GoldStar MA-1302S Page 19 Service Manual Download | Manualshive

Page: 19 / 39

background image

5-9

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1 and Rx100)
¥ Primary winding
¥ Secondary winding
¥ Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
¥ Primary winding to ground
¥ Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
¥ Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
¥ Filament to chassis

Approx.: 0.2 ~ 0.4 ohm
Approx.: 60 ~ 90 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

PRIMARY
TERMINAL

SECONDARY
TERMINAL

FILAMENT
WINDING
TERMINAL

COMPONENT TEST PROCEDURE

«
...
17
18
19
20
21
...
»

Summary of Contents for GoldStar MA-1302S








































Reviews:

No comments

Related manuals for GoldStar MA-1302S

Brand: Samsung Pages: 120

Brand: Samsung Pages: 28

Brand: Samsung Pages: 25

Brand: Samsung Pages: 24

Brand: Samsung Pages: 3

Brand: Samsung Pages: 32

Brand: Maytag Pages: 13

Brand: Oster Pages: 33

Brand: BALMUDA Pages: 20

Brand: Orbegozo Pages: 36

Brand: Sovereign Pages: 10

Brand: NEFF Pages: 56

Brand: Prestige Pages: 24

Brand: Abt Pages: 20

Brand: Farberware Pages: 20

Brand: Jenn-Air Pages: 24

Brand: linarie Pages: 12

Brand: Silverline Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands