LG GLOFA 34F - RD2A User Manual Download Page 59

Page: 59 / 60

CAUTION

Wiring Precautions

▶

When grounding a FG terminal, be sure to provide class 3 grounding which is dedicated to

the PLC. If not grounded, It can cause malfunction.

▶

Before the PLC wiring, be sure to check the rated voltage and terminal arrangement for

the module and observe them correctly.

If a different power, not of the rated voltage, is applied or wrong wiring is provided, it can

cause a fire or disorder of the module.

▶

Drive the terminal screws firmly to the defined torque.

If loosely driven, it can cause short circuit, a fire or malfunction.

▶

Be careful that any foreign matter like wire scraps should not enter into the module.

It can cause a fire, disorder or malfunction.

WARNING

Test Run and Maintenance

Precautions

▶

Do not contact the terminals

while the power is applied.
It can cause malfunction.

▶

When cleaning or driving a termi-

nal screw, perform them after the
power has been turned off

▶

Do not perform works while the

power is applied, which can
cause disorder or malfunction.

CAUTION

▶

Do not separate the module from

the printed circuit board(PCB), or
do not remodel the module.

They can cause disorder, mal-

function, damage of the module
or a fire.

When mounting or dismounting

the module, perform them after
the power has been turned off.

▶

Do not perform works while the

power is applied, which can
cause disorder or malfunction.

CAUTION

Waste Disposal Precautions

▶

When disposing the module, do it as an industrial waste.

Summary of Contents for GLOFA 34F - RD2A





























































Search results

Summary of Contents for GLOFA 34F - RD2A

Reviews:

LG GLOFA 34F - RD2A, User Manual, Page: 59 / 60

Search results

Summary of Contents for GLOFA 34F - RD2A

Reviews: