LG FB-C186HSA0 Installation Instructions Manual Download

Page: 1 / 24

CEILING DUCT TYPE AIR CONDITIONERS

INSTALLATION INSTRUCTIONS

(Refrigerant : R407C)

P/No.:

(Side)

(Rear)

Air intake

vents

Air outlet

vents

Control Cover

Connecting Wire
Connection Pipe

Drain Hose

Air filters

Air intake vents

Air outlet vents

(Side)

(Rear)

Air intake vents

Air outlet vents

Piping
Drain hose

Connecting wire

Control cover

Indoor Unit

Outdoor Unit

•

This unit is charged with new refrigerant, R407C.

•

Be sure to use proper tools for R407C, when installing the unit.

• Please read this instruction sheet completely before installing the product.

• When the power cord is damaged, replacement work shall be performed by authorized

personnel only.

• Installation work must be performed in accordance with the national wiring standards by

authorized personnel only.

MFL65000405

Remote Controller

Summary of Contents for FB-C186HSA0

























Search results

Summary of Contents for FB-C186HSA0

Reviews:

Related manuals for FB-C186HSA0

Brands by name

Popular brands

LG FB-C186HSA0, Installation Instructions Manual

Search results

Summary of Contents for FB-C186HSA0

Reviews:

Related manuals for FB-C186HSA0

Brands by name

Popular brands