manualshive.com logo in svg

LG DLE2250 Series, Service Manual, Page: 3 / 47

Share
Download
LG DLE2250 Series Service Manual Download Page 3

3

CONTENTS

1. SPECIFICATIONS  ............................................................................................................... 4

2. FEATURES AND BENEFITS  ............................................................................................... 6

3. INSTALLATION INSTRUCTIONS  .........................................................................................7

4. DRYER CYCLE PROCESS ................................................................................................ 13

5. COMPONENT TESTING INFORMATION  ......................................................................... 14

6. MOTOR DIAGRAM AND SCHEMATIC  ............................................................................. 17

7. WIRING DIAGRAM  ............................................................................................................ 18

8. FLOW SENSOR FUNCTION  ............................................................................................. 19

8-1. FLOW SENSOR  ....................................................................................................... 19
8-2. INSTALLATION  CHECK  .......................................................................................... 20
8-3. TROUBLESHOOTING FOR FLOW SENSOR DRYER  ............................................ 21

9. DIAGNOSTIC TEST  .......................................................................................................... 22

9-1. TEST 1   120V AC ELECTRICAL SUPPLY  ............................................................. 23
9-2. TEST 2   THERMISTOR TEST - MEZSURE WITH POWER OFF  .......................... 26
9-3. TEST 3   MOTOR TEST  .......................................................................................... 27
9-4. TEST 4   MOISTURE SENSOR ............................................................................... 28
9-5. TEST 5   DOOR SWITCH TEST .............................................................................. 29
9-6. TEST 6   HEATER SWITCH TEST - ELECTRIC TYPE ........................................... 30
9-7. TEST 7   GAS VALVE TEST - GAS TYPE ............................................................... 31
9-8. TEST 8   SEMI-CONDUCTOR  ................................................................................ 32

10. CHANGE GAS SETTING  (NATURAL GAS, PROPANE GAS)  ....................................... 33

11. DISASSEMBLY INSTRUCTIONS  .................................................................................... 35

12. EXPLODED VIEW ............................................................................................................ 42

12-1. Control Panel and Plate Assembly .......................................................................... 42
12-2-1. CABINET and DOOR ASSEMBLY: ELECTRIC TYPE  ........................................ 43
12-2-2. CABINET and DOOR ASSEMBLY: GAS TYPE  .................................................. 44
12-3-1. DRUM and MOTOR ASSEMBLY: ELECTRIC TYPE ........................................... 45
12-3-2. DRUM and MOTOR ASSEMBLY: GAS TYPE ..................................................... 46

Summary of Contents for DLE2250 Series
















































Reviews:

No comments