LG DLE2250 Series Page 25 Service Manual Download

Page: 25 / 47

3. Status Mode Of wrong Connection

1.Black and White Housing

2.Black Housing

3.White Housing

4.Black and White Housing

5.Black and White Housing

Off

Normal

Heater2

Off

Normal

Heater1

Off

Power Off

Power On

Power Off

Wire

CROSS

Wire

CROSS

Wire

CROSS

Housing CROSS

Housing and Wire

CROSS

Items

Case

Heater1

Operation(black)

Heater2

operation(White)

PCB condition

Of operation

1.Black and White Housing

Off

Power Off

Wire

CROSS

Items

Case

Heater1

Operation(black)

Heater2

operation(White)

PCB condition

Of operation

- Improper connection of the heater can damage the heater or the main board.

CAUTION

Connector Housing

Black

Check the Matching color Between
Harness wire and Tab Relay.
(Black Housing – Black Tab Relay)

Color

< Table 2 > : Connection of Tab Relay with PCB ASSEMBLY (Gas)

< Table1 > : Wrong Connection of the Tab Relay and Connector Housing (Elec)

< Table2 > : Wrong Connection of the Tab Relay and Connector Housing (Gas)

Harness

Remark

PCB

Tap relay 1

Blue Wire

Black Wire

Connector Housing

Summary of Contents for DLE2250 Series
















































Search results

Summary of Contents for DLE2250 Series

Reviews:

Related manuals for DLE2250 Series

Brands by name

Popular brands

LG DLE2250 Series, Service Manual

Search results

Summary of Contents for DLE2250 Series

Reviews:

Related manuals for DLE2250 Series

Brands by name

Popular brands