LG CordZero A9 Series Svc Manual Download Page 24 | Manualshive

Page: 24 / 43

background image

-24-

5. How to disassemble the inlet motor(floor inlet)

(1) Disassemble the inlet

roller (Refer to how to
disassemble the inletroller
in details)

(2) Remove the cover of the

right bump with a hand.

(3) Remove 4 screws in the

red circle.

(4) Remove the cover below

the inlet after removing
the 4 screws.

(5) Remove the bump in the

figure with a hand.

(6) Remove the top cover of

the inlet.

(7) Remove the inlet motor.

(8) Remove the motor

harness connector and
replace the motor.

(9) Reassemble the whole part

in the reverse sequence.

Disassembly, assembly and repairing of main parts

«
...
22
23
24
25
26
...
»

Summary of Contents for CordZero A9 Series












































Reviews:

No comments

Related manuals for CordZero A9 Series

Brand: KENT Pages: 11

Brand: Bionaire Pages: 2

Brand: Vax Pages: 4

Brand: TCL Pages: 17

Brand: Kerrick Pages: 16

Brand: 420Purifier Pages: 2

Brand: XPERT Pages: 9

Brand: Winix Pages: 72

Brand: CleanMax Pages: 12

Brand: Faton Pages: 98

Brand: Vax Pages: 16

Brand: Vacmaster Pages: 14

Brand: Nikro Pages: 11

Brand: Far Tools Pages: 18

Brand: Vax Pages: 12

Brand: DS Produkte Pages: 6

Brand: DS Produkte Pages: 6

Brand: DS Produkte Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands