LG CM9530 Service Manual Download Page 40

Page: 40 / 87

3-21

%WB5;5

%WB7;5

%WB5765

%WB&765

< Signal check point >

ONE POINT REPAIR GUIDE

NO SOUND

There is no sound output in the BLUETOOTH FUNCTION, repair the set according to
the following guide.

6-7. IN THE BLUETOOTH FUNCTION

6-7-1. Solution

Please check and replace IC501 on MAIN board and Bluetooth module on front panel.

6-7-2. How to troubleshoot (Countermeasure)

1) Check BT_RX, BT_TX signal to Pin5, 7 of CN504.

If no signal, check the signal to Pin5, 7 and Pin1(+3.3 V) of on the Bluetooth module and cable connection state.

If there are no signal out from module, replace new module.

2) Check if BT_RX/TX is entered from Pin5, 7 of CN504 to Pin169, 170 to IC501 (DSP).
3) Check if MIC_BCK, MIC_MLCK & MIC_O_DATA is entered from IC501 to IC600.

If no signal, check VCC12(+1.2 V) for IC501. If it is abnormal, change replace it a new one.

4) Check the following I2S signal flow from IC501 to IC600.

If there is any trouble, check the power for each IC. If the signals are abnormal, replace it a new one.

5) Check if the digital audio AMP block is okay. Refer to “Digital Audio AMP” guide.

If AMP is damaged, replace it with a new one.

6-7-3. Service hint (Any picture / Remark)

IC501

MLC3700

IC600

TAS5548

PWM

DAC_BCK

DAC_LRCK

DAC_DATA

IR AMP

IRF6775

B/T Module

BT_RX,

BT_TX

< BLUETOOTH function signal

ow >

Summary of Contents for CM9530
























































































Search results

Summary of Contents for CM9530

Reviews:

Related manuals for CM9530

Brands by name

Popular brands

LG CM9530, Service Manual

Search results

Summary of Contents for CM9530

Reviews:

Related manuals for CM9530

Brands by name

Popular brands