LG CM9530 Service Manual Download Page 33

Page: 33 / 87

3-14

ONE POINT REPAIR GUIDE

NO OPERATION OF MD

When no sound output in the CD function, you can not listen to music reading data
from a CD disc if the pickup module in MD doesn’t work. This step is for checking the
LASER FOCUSING ACTUATOR.

5-5. LASER FOCUSING ACTUATOR

5-5-1. Solution

Please check and replace IC407, IC408 on MAIN board.

5-5-2. How to troubleshoot (Countermeasure)

The focusing actuator makes the laser beam keep a regular interval with the surface of a CD disc.
1) Check the FOD signal from Pin13 of IC407.

If no signal, check 3.3 V(RF) and X402.

2) Check F- & F+ from IC408 to CN404 for driving the focusing actuator.

If no signal, check +1.8 V and +5 V for IC408.

3) Check if the FFC cable is solidly connected between CN404 and MD.
4) Check the MD.

If the pick-up module has any trouble, it can not move the laser beam on the top or bottom side.

Please check the function after changing another MD.

5-5-3. Service hint (Any picture / Remark)

mT Gju[W[

mRGGju[W[

)

SLQRI&1

)

SLQRI&1

< Waveform of TR±

for driving FOCUSING actuator >

< Signal check point >

Summary of Contents for CM9530
























































































Search results

Summary of Contents for CM9530

Reviews:

Related manuals for CM9530

Brands by name

Popular brands

LG CM9530, Service Manual

Search results

Summary of Contents for CM9530

Reviews:

Related manuals for CM9530

Brands by name

Popular brands