LG CM9520 Service Manual Download Page 38

Page: 38 / 109

3-9

Does the customer select correctly

the USB function he or she wants to listen to?

Make sure to insert a USB into the USB ports.

YES

Is “USB” displayed on VFD?

Make sure to select the USB function

pressing the CD/USB button.

YES

Does the unit display “SELECTED” on VFD

when a USB is inserted into the USB port?

When “No USB” is displayed,

make sure that the customer uses the recommended

USB which support USB2.0 or USB1.1.

YES

Does the customer use the supported

mp3 or WMA music files on the disc?

Check if it is the playable disc or not.

Make sure that the file extensions are

“.mp3”or “.wma”.

YES

When the unit searches music files in a USB,

are the following messages displayed on VFD?

“SELECTED” “TRACKING #” and “TIME”.

Make sure to check the compatible USB device

and the supported MP3/WMA music file requirement.

Refer to the owner’s manual.

YES

After selecting a track number using the SCAN button,

press PLAY button and turn the master volume

clockwise for the volume up.

The volume level LEDs around the master volume

will be turned on more and more

while turning it clockwise for the volume up.

YES

Are the sound spectrum level

on the left and right side of the front panel

being changed up and down

according to the sound input gain?

The sound spectrum level will be turned on/off

repeatedly at regular intervals. A speaker cable

might be short-circuited with the chassis ground.

Be careful not to be shorted each other.

YES

Are the speaker cables connected correctly

between the speaker terminals on the unit

and the speakers?

Make sure to connect the cables

to each specified connector tightly on the unit.

Connect the woofer cables to the WOOF SYSTEM

connectors on the rear panel.

7. NO SOUND IN USB FUNCTION

TRAINING MASTER

Summary of Contents for CM9520














































































































Search results

Summary of Contents for CM9520

Reviews:

Related manuals for CM9520

Brands by name

Popular brands

LG CM9520, Service Manual

Search results

Summary of Contents for CM9520

Reviews:

Related manuals for CM9520

Brands by name

Popular brands