LG CM9520 Service Manual Download Page 39

Page: 39 / 109

3-10

The sound is output from the speakers.

Sound OK

YES

Is the power cord plugged

into a electrical outlet?

Make sure to plug the power cord of the unit

into a electrical outlet.

YES

Does the Standby LED light

in red color?

If the customer can not see the red light

on the front panel, the SMPS might have any problem.

Please solve the problem

referring to the service manual.

YES

Is the Standby LED turned off

after pressing the Power button

on the remote control?

Replace the batteries with new ones

if the remote control doesn’t work.

YES

Are the messages displayed

in the following order on VFD?

“HELLO” “VOLUME 15” “FUNCTION”

The SMPS might be not able to supply the power

to drive the VFD.

Refer to the service manual to fix it.

YES

Is there any sound

from the speakers each input function?

Make sure to connect speaker cables.

YES

Power & Sound OK

8. NO POWER

TRAINING MASTER

Summary of Contents for CM9520














































































































Search results

Summary of Contents for CM9520

Reviews:

Related manuals for CM9520

Brands by name

Popular brands

LG CM9520, Service Manual

Search results

Summary of Contents for CM9520

Reviews:

Related manuals for CM9520

Brands by name

Popular brands