LG CM9520 Service Manual Download Page 35

Page: 35 / 109

3-6

Does the customer select correctly

the AM/FM function he or she wants to listen to?

Make sure to connect AM/FM antennas

on the rear panel of the unit.

YES

Is “AM or FM” displayed on VFD?

Make sure to select AM or FM function

pressing the TUNER button.

YES

After tuning a desired channel

using the TUNING± button,

is the sound quality good to listen to the music?

To prevent noise pickup, keep the AM Loop

antenna away from the unit and other components.

Be sure to fully extend the FM wire antenna. After

connecting the FM wire antenna, keep it horizontal.

YES

Is the signal strength of the radio station too week?

Make sure to tune the station manually.

YES

Are the sound spectrum level LED’s

on the left and right side of the front panel

being changed up and down

according to the sound input gain?

The sound spectrum level LED’s will be turned on/off

repeatedly at regular intervals. A speaker cable might

be short-circuited with the chassis ground.

Be careful not to be shorted each other.

YES

Are the speaker cables connected correctly

between the speaker terminals on the unit

and the speakers?

Make sure to connect the cables to each specified

connector tightly on the unit.

Connect the woofer cables to the WOOF SYSTEM

connectors on the rear panel.

YES

The sound is output from the speakers.

YES

Sound OK

5. NO SOUND IN AM/FM FUNCTION

TRAINING MASTER

Summary of Contents for CM9520














































































































Search results

Summary of Contents for CM9520

Reviews:

Related manuals for CM9520

Brands by name

Popular brands

LG CM9520, Service Manual

Search results

Summary of Contents for CM9520

Reviews:

Related manuals for CM9520

Brands by name

Popular brands