background image

4

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

Operation

• Do not share the outlet with other appliances. It will cause an electric shock or a fire due to heat

generation.

• Do not use the damaged power cord. Otherwise, it may cause a fire or electrical shock.

• Do not modify or extend the power cord randomly. Otherwise, it may cause a fire or electrical

shock.

• Take care so that the power cord may not be pulled during operation. Otherwise, it may cause a fire

or electrical shock.

• Unplug the unit if strange sounds, smell, or smoke comes from it. Otherwise, it may cause electrical

shock or a fire.

• Keep the flames away. Otherwise, it may cause a fire.

• Take the power plug out if necessary, holding the head of the plug and do not touch it with wet

hands. Otherwise, it may cause a fire or electrical shock.

• Do not use the power cord near the heating tools. Otherwise, it may cause a fire and electrical

shock.

• Do not open the suction inlet of the indoor/outdoor unit during operation.

Otherwise, it may electrical shock and failure. 

• Do not allow water to run into electrical parts. Otherwise, it may cause the failure of machine or

electrical shock.

• Hold the plug by the head when taking it out. It may cause electric shock and damage.

• Never touch the metal parts of the unit when removing the filter. They are sharp and may cause

injury.

• Do not step on the indoor/outdoor unit and do not put anything on it. It may cause an injury through

dropping of the unit or falling down.

• Do not place a heavy object on the power cord. Otherwise, it may cause a fire or electrical shock.

• When the product is submerged into water, always contact the service center. Otherwise, it may

cause a fire or electrical shock.

• Take care so that children may not step on the outdoor unit. Otherwise, children may be seriously

injured due to falling down. 

CAUTION

Installation

• Install the drain hose to ensure that drain can be securely done. Otherwise, it may cause water leak-

age.

• Install the product so that the noise or hot wind from the outdoor unit may not cause any damage to

the neighbors. Otherwise, it may cause dispute with the neighbors.

• Always inspect gas leakage after the installation and repair of product. Otherwise, it may cause the

failure of product.

• Keep level parallel in installing the product. Otherwise, it may cause vibration or water leakage.

Operation

• Avoid excessive cooling and perform ventilation sometimes. Otherwise, it may do harm to your

health.

• Use a soft cloth to clean. Do not use wax, thinner, or a strong detergent. The appearance of the air

conditioner may deteriorate, change color, or develop surface flaws.

• Do not use an appliance for special purposes such as preserving animals vegetables, precision

machine, or art articles. Otherwise, it may damage your properties.

• Do not place obstacles around the flow inlet or outlet. Otherwise, it may cause the failure of appli-

ance or an accident.

!

Summary of Contents for AVUQ36GM1A0


























Reviews: