background image

MAINTENANCE AND SERVICE

29

ENGLISH

Do not overcool the room.

This is not good for the health
and wastes electricity.

Keep blinds or curtains closed.

Do not let direct sunshine
enter the room when the air
conditioner is in operation.

Keep the room temperature
uniform.

Adjust the vertical and hori-
zontal airflow direction to en-
sure a uniform temperature in
the room.

Make sure that the doors 
and windows are shut tight.

Avoid opening doors and win-
dows as much as possible to
keep the cool air in the room.

Clean the air filter regularly.

Blockages in the air filter re-
duce the airflow and lower
cooling and dehumidifying ef-
fects. Clean at least once
every two weeks.

Ventilate the room occasion-
ally.

Since windows are kept
closed, it is a good idea to
open them and ventilate the
room now and then.

When the air conditioner is not
going....

When air conditioner is not going to
be used for a long time.

Operate the air conditioner at the following
settings for 2 to 3 hours.

Type of operation: Fan operation
mode.(Refer to page 19.)

This will dry out the internal mechanisms.

Turn off the breaker.

Remove the batteries from the Remote Con-
troller.

Helpful information

The air filters and your electiric bill.

If the air filters become clogged with dust, the
cooling capacity will drop, and 6% of the elec-
tricity used to operate the air conditioner will
be wasted.

When the air conditioner is to be
used again.

Clean the air filter and install it in the indoor
unit. (Refer to page 25 for cleaning it.)

Check that the air inlet and outlet of the in-
door/outdoor unit are not blocked.

Check that the ground wire is connected cor-
rectly. It may be connect to the indoor unit
side.

CAUTION

Turn off the breaker when the air condi-
tioner is not going to be used for a long
time.
Dirt may collect and may cause a fire.

Operation Tips!

!

Summary of Contents for ATNQ18GQSK1

































Reviews: