LG ARUB100LT3 Installation Manual Download Page 17

Page: 17 / 133

Foundation for Installation

• Fix the unit tightly with bolts as shown below so that unit will not fall down due to earthquake or gust.

• Use the H-beam support as a base support

• Noise and vibration may occur from the floor or wall since vibration is transferred through the installation

part depending on installation status. Thus, use anti-vibration materials (cushion pad) fully (The base pad
shall be more than 200mm).

WARNING

• Install where it can sufficiently support the weight of the outdoor unit.

If the support strength is not enough, the outdoor unit may drop and hurt people.

• Install where the outdoor unit may not fall in strong wind or earthquake.

If there is a fault in the supporting conditions, the outdoor unit may fall and hurt people.

• Please take extra cautions on the supporting strength of the ground, water outlet treatment(treat-

ment of the water flowing out of the outdoor unit in operation), and the passages of the pipe and
wiring, when making the ground support.

• Do not use tube or pipe for water outlet in the Base pan. Use drainage instead for water outlet.

The tube or pipe may freeze and the water may not be drained.

WARNING

• Be sure to remove the Pallet(Wood Support) of the bottom

side of the outdoor unit Base Pan before fixing the bolt. It
may cause the unstable state of the outdoor settlement,
and may cause freezing of the heat exchanger resulting in
abnormal operations.

• Be sure to remove the Pallet(Wood Support) of the bottom

side of the outdoor unit before welding. Not removing
Pallet(Wood Support) causes hazard of fire during welding.

At least 200mm

Unit : mm

200

100

- The corner part must be fixed firmly. Otherwise, the

support for the installation may be bent.

- Get and use M10 Anchor bolt.
- Put Cushion Pad between the outdoor unit and ground

support for the vibration protection in wide area.

- Space for pipes and wiring (Pipes and wirings for bot-

tom side)

- H-beam support
- Concrete support

Pallet(Wood Support)
- Remove before Installation

Installation Manual

Installation

ENGLISH

Summary of Contents for ARUB100LT3






































































































































Search results

Summary of Contents for ARUB100LT3

Reviews:

Related manuals for ARUB100LT3

Brands by name

Popular brands

LG ARUB100LT3, Installation Manual

Search results

Summary of Contents for ARUB100LT3

Reviews:

Related manuals for ARUB100LT3

Brands by name

Popular brands