background image

aria

186/ 100/ 34E - DIGITAL KEY TELEPHONE SYSTEM  USER GUIDE

30

Button

Procedure

To start the traffic analysis at system attendant,

Press 

TRANS/PGM

button.

Dial  

# 7 1

.

Press 

HOLD/SAVE

button.

To stop the traffic analysis at system attendant,

Press 

TRANS/PGM

button.

Dial  

# 7 2

.

Press 

HOLD/SAVE

button.

To print the result of traffic analysis at system attendant,

Press 

TRANS/PGM

button.

Dial  

# 7 3

.

Press 

HOLD/SAVE

button.

To abort printing at system attendant,

Press 

TRANS/PGM

button.

Dial  

# 7 4

.

Press 

HOLD/SAVE

button.

The system will monitor the system and record various traffic data which can be printed upon request. The 
information can be used to determine whether the circuits installed in the systemare adequate. 

When enabled, it will continue to monitor the traffic until disabled. The traffic data is 

collected and sent to the RS232C port upon request. The collected traffic data contains two types of traffic 
data. The first type is peg counts which give an actual count of the number of times a particular 
operation has occurred. Peg counts are given in absolute values from 00000 to 99999. The second type of 
data is usage times which give the average percent occupancy of a device, i.e., stations, CO lines, DTMF 
receivers, etc. Usage times are given in seconds from 00000 to 99999. Counts and times are cumulative 
from the time the monitoring is activated, and are reset by initiating the start up procedure again.

Traffic Analysis 

Attendant Operation

Button

Procedure

Attendant LCD Language 

To change the LCD language at attendant,

Press 

TRANS/PGM

button.

Dial  

5 1 

Dial the station range to be changed.

Select the language type with the following codes.

Press 

HOLD/SAVE

button.

aria

186     

aria

34E/100              Language

0 0                  0 0          

English

0 1                  0 1               Korean
0 2                  0 2               Italian
0 3                  0 3               English for Large LCD
0 4                  0 4               Swedish
0 5                  0 5               Norwegian
0 6                  0 6               Finnish
0 7                  0 7               Dutch
0 8                  0 8               Spanish
0 9                  0 9               Korean for Large LCD
1 0                  1 0               Danish

. .                   1 1               German
. .                   1 2               German for Large LCD

aria

186     

aria

34E/100              Language

1 3                  1 3               Estonia 
1 2                  1 4               Estonia for Large LCD
1 4                  1 5               Swedish for Large LCD
1 5                  1 6               Italy for Large LCD
1 6                  1 7               Norway for Large LCD  
1 7                  1 8               Finnish for Large LCD
1 8                  1 9               Dutch for Large LCD
2 0                  2 0               Russian

9                   2 1               Spanish for Large LCD

2 1                  2 2               Russian for Large LCD
1 1                  2 3               Danish for Large LCD
2 2                  2 4               Portuguese  

. .                   2 5               Portuguese for Large LCD   

Summary of Contents for Aria 34E






































Reviews: