background image

4

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

• Do not install the product on a defective installation stand.

- It may cause injury, accident, or damage to the product.

• Be sure the installation area does not deteriorate with age.

- If the base collapses, the air conditioner could fall with it, causing property damage, product failure,

and personal injury.

• Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or air purge. Do not compress

air or Oxygen and do not use Flammable gases. Otherwise, it may cause fire or explosion.
- There is the risk of death, injury, fire or explosion.

• Do not turn on the breaker or power under condition that front panel, cabinet, top cover, control box

cover are removed or opened. Otherwise, it may cause fire, electric shock, explosion or death.

Operation

• Take care to ensure that power cable could not be pulled out or damaged during operation.

There is risk of fire or electric shock.

• Do not place anything on the power cable. There is risk of fire or electric shock.
• Do not touch(operate) the product with wet hands. There is risk of fire or electrical shock.
• Do not place a heater or other appliances near the power cable. There is risk of fire and elec-

tric shock.

• Do not allow water to run into electric parts. There is risk of fire, failure of the product, or elec-

tric shock.

• Do not store or use flammable gas or combustibles near the product. There is risk of fire or

failure of product.

• Do not use the product in a tightly closed space for a long time. Oxygen deficiency could

occur.

• When flammable gas leaks, turn off the gas and open a window for ventilation before turn the

product on. Do not use the telephone or turn switches on or off. There is risk of explosion or
fire.

• If strange sound, smell or smoke comes from product, turn the breaker off or disconnect the

power supply cable. There is risk of electric shock or fire.

• Stop operation and close the window in storm or hurricane. If possible, remove the product

from the window before the hurricane arrives. There is risk of property damage, failure of
product or electric shock.

• Do not open the inlet grill of the product during operation.(Do not touch the electrostatic filter,

if the unit is so equipped.) There is risk of physical injury, electric shock, or product failure.

• When the product is soaked (flooded or submerged), contact an authorized service center.

There is risk of fire or electric shock.

• Be cautious that water could not enter the product. There is risk of fire, electric shock, or

product damage.

• Ventilate the product from time to time when operating it together with a stove, etc. There is

risk of fire or electric shock.

• Turn the main power off when cleaning or maintaining the product. There is risk of electric

shock.

• When the product is not be used for a long time or the product use first time after test run-

ning, turn on main power switch before 6hours ago.

• Take care to ensure that nobody could step on or fall onto the outdoor unit. This could result

in personal injury and product damage.

1,MFL67448529,영영  2017. 6. 19.  영영 3:45  Page 4

Summary of Contents for APUQ24GS1A4

















































Reviews: