LG-Ericsson IPECS GDC-480H User Manual Download Page 59 | Manualshive

Page: 59 / 70

background image

GDC-480H Wireless Handset
User Guide

49

5.6.13 Auto

Release

Mode

The Auto Release Mode allows you to disconnect a call automatically during a conversation
by putting the handset into charger. The default is ON.

To enable or disable Auto Release Mode:

1. Select the Phone Settings menu from the User Menu.
2. Use the

Navigation

( ) button to highlight the Auto Release Mode selection.

3. Press the

OK

( ) left soft button to access the sub-menu.

4. Use the left or right arrow of the

Navigation

( ) button to select Yes or No.

5. Press the

OK

( ) left soft button to accept it.

6. Press the

End

( ) button.

5.6.14 Emergency

Call

In emergency situations you can connect the designation number by pressing Emergency
button at the upper side of handset. The change of the designation number is available and
the default is Off.

To enable or disable Emergency call:

1. Select the Phone Settings menu from the User Menu.
2. Use the

Navigation

( ) button to highlight the Emergency Call selection.

3. Press the

OK

( ) left soft button to access the sub-menu.

4. Use the left or right arrow of the

Navigation

( ) button to select Yes or No.

5. Press the

OK

( ) left soft button to accept it.

6. Press the

End

( ) button.

5.6.15

Block Dialed Call

From the User Menu, select the Phone Register menu.

1. Use the

Navigation

( ) button to highlight a selection.

2. Press the

OK

( ) left soft button; PIN request will display.

3. Use the dial pad to enter your PIN.
4. Use the left or right arrow of the

Navigation

( ) button to select Yes or No.

5. Press the

OK

( ) left soft button to accept it.

6. Press the

End

( ) button.

5.7 Phone Register

To register a new wireless terminal to your base or to register a wireless terminal again after
base reset (refer to the Section Reset).

1. Press the

Menu

( ) button to display the User menu.

2. From the User Menu use the

Navigation

( ) button to highlight Phone Register.

3. Press the

OK

( ) left soft button. This displays the Phone Register menu.



Subscription



Base

Choice



Modify

PIN

«
...
57
58
59
60
61
...
»

Summary of Contents for IPECS GDC-480H







































































Reviews:

No comments

Related manuals for IPECS GDC-480H

Yealink SIP-T46G

Brand: Yealink Pages: 6

Brand: Yealink Pages: 176

Brand: Alcatel Pages: 51

Brand: Archos Pages: 40

OneTouch X1 7053D

Brand: Alcatel Pages: 20

Brand: Blackberry Pages: 6

Brand: Grandstream Networks Pages: 50

Brand: SoftBank Pages: 9

Brand: Doogee Pages: 39

Brand: Tecno Mobili Pages: 16

Brand: Livoo Pages: 4

Brand: Polycom Pages: 2

Brand: Zte Pages: 2

Brand: GE Pages: 2

Cell Fusion 28129FE2

Brand: GE Pages: 2

Cell Fusion 28127FE1

Brand: GE Pages: 2

Brand: GE Pages: 42

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands