LG-Ericsson iPECS ES-2024G Installation Manual Download Page 31

Page: 31 / 60

HAPTER

| Installing the Switch

Optional Rack-Mounting Equipment

– 31 –

ES-2024G/2024GP

PTIONAL

ACK

-M

OUNTING

QUIPMENT

If you plan to rack-mount the switch, be sure to have the following

equipment available:

◆

Four mounting screws for each device you plan to install in a rack—

these are not included

◆

A screwdriver (Phillips or flathead, depending on the type of screws

used)

OUNTING

The switch can be mounted in a standard 19-inch equipment rack or on a

desktop or shelf. Mounting instructions for each type of site follow.

AUTION

Stacking switches without enough space for airflow can damage

the switch. Attach rubber feet to the bottom of the switch and make sure

there is sufficient space around the installed switch for airflow.

ACK

OUNTING

Before rack mounting the switch, pay particular attention to the following

factors:

◆

Temperature: Since the temperature within a rack assembly may be

higher than the ambient room temperature, check that the rack-

environment temperature is within the specified operating temperature

range. (

“Physical Characteristics” on page 50.

)

◆

Mechanical Loading: Do not place any equipment on top of the rack-

mounted unit.

◆

Circuit Overloading: Be sure that the supply circuit to the rack

assembly is not overloaded.

◆

Grounding: Rack-mounted equipment should be properly grounded.

Particular attention should be given to supply connections other than

direct connections to the mains.

Summary of Contents for iPECS ES-2024G





























































Search results

Summary of Contents for iPECS ES-2024G

Reviews:

Related manuals for iPECS ES-2024G

Brands by name

Popular brands

LG-Ericsson iPECS ES-2024G, Installation Manual

Search results

Summary of Contents for iPECS ES-2024G

Reviews:

Related manuals for iPECS ES-2024G

Brands by name

Popular brands