LG-Ericsson GDC-450H User Manual Download Page 59

Page: 59 / 66

GDC-450H Wireless Handset
User Guide

7 Troubleshooting

Problem

Possible Cause

Solution

LCD is blank

No power

Assure batteries are properly installed and
charged. Press and hold the End/Power
button for 1 second.

“NO CHANNEL” displayed
when TALK button
pressed

All DECT channels
are in use.

Wait until a channel is available.

Low or high audio volume

Volume needs
adjusting

While connected to a call, press Up or
Down arrow on the Navigation button.

Low or high ring volume

Volume needs
adjusting

Adjust Ring volume level; refer to

Image and

Sounds

Section.

“UNREGISTERED”
displayed
in the LCD

No active
subscription

Subscribe the handset, refer to

Subscribing

the GCD-450H to a System

Low battery icon ( ) is
flashing on LCD with
warning tone

Battery level is low

Recharge the battery.

Power-OFF right after
power-ON

Battery level is
below operational
state.

Recharge the battery.

Insufficient RF from
base station, no RF-
lock to base station.

Move to obtain higher RSSI; wait for RF-
lock to base station.

Tone is low or high when
pressing a digit

Keypad tones are
disabled or tones
volume needs
adjusting.

Use Up and down arrow on Navigation
button to adjust volume. Check Keypad
Tones are enabled/disabled in the User
Menu.

Unexpected call
disconnect or call failure

Poor RF
environment.

RF can change over time, move to obtain
higher RSSI.

Battery duration is less
than specified

Batteries failing
and/or poor battery
charging habits

Charge batteries and keep handset in
cradle when not in use; refer to

Installing the

Batteries

Section.

Subscription fails

Interference from
other DECT system.
Too far from Base
station, no available
channel or wrong
Base station (RFPI)
or Auth code
selected.

Turn other DECT systems Off.
Assure handset is in range of base station.
Assure RFPI and AC are correct.
Wait for an available wireless channel.

When pressing TALK
button, the Phone icon
(

) blinks several times

and disappears

Subscription error

Terminate the subscription and re-
subscribe.

When pressing TALK
button, nothing happens

Out-of-range

Assure the handset is locked to a Base
station and RSSI is at least two (2) bars.

Summary of Contents for GDC-450H



































































Search results

Summary of Contents for GDC-450H

Reviews:

Related manuals for GDC-450H

Brands by name

Popular brands

LG-Ericsson GDC-450H, User Manual

Search results

Summary of Contents for GDC-450H

Reviews:

Related manuals for GDC-450H

Brands by name

Popular brands