Lexmark 2480 - Forms Printer B/W Dot-matrix Service Manual Download Page 68

Page: 68 / 170

4-8

Service Manual

24xx

Covers, Top Removal

1. Turn the printer off and disconnect the power cord at the printer.

2. Remove the tractor assembly, if it is installed in the pull tractor

position, by pressing the locking levers and pulling the tractor
assembly out of the printer.

3. Remove the ribbon access cover. Go to

“Covers, Ribbon

Access Removal” on page 4-6

4. Remove the front cover. Go to

“Covers, Front Removal” on

page 4-6

5. Remove the option cover. Go to

“Covers, Option Removal” on

page 4-7

Note: With the option cover removed, you can see the operator
panel cable attached to the logic board.

6. Disconnect the operator panel cable from the logic board.

7. Remove the two screws [A] from each side of the front cover

area.

Summary of Contents for 2480 - Forms Printer B/W Dot-matrix











































































































































































Search results

Summary of Contents for 2480 - Forms Printer B/W Dot-matrix

Reviews:

Related manuals for 2480 - Forms Printer B/W Dot-matrix

Brands by name

Popular brands

Lexmark 2480 - Forms Printer B/W Dot-matrix, Service Manual

Search results

Summary of Contents for 2480 - Forms Printer B/W Dot-matrix

Reviews:

Related manuals for 2480 - Forms Printer B/W Dot-matrix

Brands by name

Popular brands