Lexmark 2480 - Forms Printer B/W Dot-matrix Service Manual Download Page 14

Page: 14 / 170

1-2

Service Manual

24xx

Setup Mode

Entering Setup Mode

1. Open the operator panel cover to access layer two.

2. Press Setup to put the printer in setup mode and print the Main

Menu.

3. Press LineFeed to print a list of all the available options.

4. Select any option from the Main Menu by pressing the

corresponding button. A new menu prints each time you press a
button, displaying new selections.

5. After making your selection, the printer prints a page with the

changes shown.

Exiting Setup Mode

1. Press Set TOF until the printer returns to the Main Menu, or

press Pitch from any menu containing a Return to Main Menu
selection.

2. Press Set TOF again to exit Setup mode. New settings are

saved only when the printer exits Setup mode.

Note: If the printer runs out of paper while using Setup mode, load
more paper into the tractor pins and press Setup to continue.

Summary of Contents for 2480 - Forms Printer B/W Dot-matrix











































































































































































Search results

Summary of Contents for 2480 - Forms Printer B/W Dot-matrix

Reviews:

Related manuals for 2480 - Forms Printer B/W Dot-matrix

Brands by name

Popular brands

Lexmark 2480 - Forms Printer B/W Dot-matrix, Service Manual

Search results

Summary of Contents for 2480 - Forms Printer B/W Dot-matrix

Reviews:

Related manuals for 2480 - Forms Printer B/W Dot-matrix

Brands by name

Popular brands