Lexmark 2070 Color Jetprinter Service Manual Download | Manualshive

Page: 34 / 78

background image

4-2

4090-001

Adjustments

The user is directed, in the Printer Control program, to perform the
head to head and bidirectional alignment adjustments after replacing
a print cartridge.

Removal Procedures

The following procedures are arranged according to the name of the
printer part discussed. Unplug the power cord before removing any
parts.

Releasing Plastic Latches

Many of the parts are held in place with plastic latches. The latches
break easily; release them carefully. To remove such parts, press the
hook end of the latch away from the part to which it is latched.

Never apply excessive force
when releasing the hook.

Hook

«
...
32
33
34
35
36
...
»

Summary of Contents for 2070 Color Jetprinter















































































Reviews:

No comments

Related manuals for 2070 Color Jetprinter

Brand: Oki Pages: 2

Brand: Pantum Pages: 105

Brand: Panasonic Pages: 83

Brand: Samsung Pages: 9

Bixolon SRP-500

Brand: Samsung Pages: 27

550N - CLP Color Laser Printer

Brand: Samsung Pages: 288

2 COLOR THERMAL PRINTER SRP-275

Brand: Samsung Pages: 8

Brand: Samsung Pages: 6

Brand: Samsung Pages: 91

Brand: JICCODA Pages: 46

Brand: uBuild-3D Pages: 12

Brand: BALCO Pages: 24

Brand: Xerox Pages: 3

Brand: Xerox Pages: 2

WorkCentre 3615

Brand: Xerox Pages: 20

Brand: Xerox Pages: 130

Brand: Xerox Pages: 793

DocuPrint C3055 DX

Brand: Xerox Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands