Lexmark 2070 Color Jetprinter Service Manual Download | Manualshive

Page: 52 / 78

background image

4-20

4090-001

Rear Cover Removal

1. Remove the front cover.

2. Place a screwdriver in slot [A] and release the cover latches.

3. Slide the cover up and off the printer.

4. To reassemble, place the cover over the tabs in the bottom

cover and press down until the cover latches. Be sure the
parallel connector snaps do not get trapped behind the cover.

Right Side Frame Assembly Removal

1. Remove the front cover.

2. Remove the rear cover.

3. Remove the carrier frame assembly.

4. Remove the paper load door and manual insert tray.

5. Remove the two screws securing the right side frame to the

back plate. Slide the right side frame off the back plate. Note the
relationship of the parts.

A

A

«
...
50
51
52
53
54
...
»

Summary of Contents for 2070 Color Jetprinter















































































Reviews:

No comments

Related manuals for 2070 Color Jetprinter

Brand: LabelTac Pages: 2

Brand: DataCard Pages: 2

Brand: FELIXprinters Pages: 66

Brand: Radio Shack Pages: 57

Brand: Sagem Pages: 86

Brand: Xerox Pages: 13

Brand: ABLE Pages: 42

Brand: Ricoh Pages: 159

Brand: Citizen Pages: 46

Brand: Oki Pages: 137

invitrogen EVOS FL

Brand: Thermo Scientific Pages: 6

Brand: FujiFilm Pages: 28

Brand: Triumph Adler Pages: 202

Brand: Oce Pages: 61

Brand: Epson Pages: 105

Brand: Epson Pages: 128

Brand: Epson Pages: 145

Brand: Epson Pages: 200

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands