manualshive.com logo in svg

Leviton evr-green EV320, Installation Manual, Page: 16 / 18

Share
Download
Leviton evr-green EV320 Installation Manual Download Page 16

10 MAINTENANCE AND REPAIR

16

10.1  Daily Maintenance

WARNINGS

• 

Avoid moisture or water in the charger. If there is water or moisture, it is necessary to immediately 
power off to avoid immediate danger, and notify professional personnel to carry out maintenance 
before next use.

CAUTIONS

• 

Please keep the charger clean and in a clean area with low humidity.  
Do not install it in an environment near the sea, with high oil, high humidity, or high dust.

• 

If there is any damage or dirt on the vehicle connector, charging cable, or vehicle connector 
holder, please contact the maintenance personnel immediately.

• 

Please use the charger properly. Do not hit or press hard on the case. If the case is damaged, 
please contact a professional technician.

• 

Avoid placing the charger near hot objects and at high temperature locations and away from 
dangerous substances such as flammable gases and corrosive materials.

• 

Do not place external objects or heavy objects on the charger to avoid danger.

WEB 

VERSION

Summary of Contents for evr-green EV320



















Reviews:

No comments