LevelOne FCS-4201 User Manual Download Page 58

Page: 58 / 66

Network Camera User’s Manual

58/66

backup file. If you have set up a fixed IP or other special settings for your device, it is not
suggested to upload a settings backup file.

“Upgrade firmware”

Select the firmware file and click upgrade button. Please be

aware that you should not turn off the power during updating the firmware and wait for
finish message.

Warning:

The upgrade firmware procedure cannot be interrupted. If the power

and/or network connection are broken during the procedure, it might possibly
cause serious damage to the Network Camera.

Note: When upgrade firmware please wait for 210~360 seconds, and then you
can connect to Network Camera again. The system will restart and require the
installer program to set up the network again.

Summary of Contents for FCS-4201



































































Search results

Summary of Contents for FCS-4201

Reviews:

Related manuals for FCS-4201

Brands by name

Popular brands

LevelOne FCS-4201, User Manual

Search results

Summary of Contents for FCS-4201

Reviews:

Related manuals for FCS-4201

Brands by name

Popular brands