LevelOne FCS-4201 User Manual Download Page 55

Page: 55 / 66

Network Camera User’s Manual

55/66

Syslog

The Network camera supports log the system messages on remote server.
The  protocol  is  compliant  to  RFC  3164.  If  you  have  external  Linux  server  with  sys  log
service,  use

“-r” option to turn on the facility for receiving log from remote machine. Or

you can use some software on Windows that is compliant to RFC 3164. An example is
Kiwi Syslog Daemon. Visit

http://www.kiwisyslog.com/kiwi-syslog-daemon-overview/.

Check

“Setup

” and “

Enable

” then input the

“IP address

” and

“port”

number of the log

server to enable the remote log facility.
In the

“Current log”

, it displays the current system log file. The content of the log

provides useful information about configuration and connection after system boot- up.

“finish”

Click on this button to save modify settings.

Summary of Contents for FCS-4201



































































Search results

Summary of Contents for FCS-4201

Reviews:

Related manuals for FCS-4201

Brands by name

Popular brands

LevelOne FCS-4201, User Manual

Search results

Summary of Contents for FCS-4201

Reviews:

Related manuals for FCS-4201

Brands by name

Popular brands