Level LIS2010-MT-1800/11 User Manual Download Page 15

25

24

Passage Mode: door can be opened from outside by simply turning the handle. Under passage mode, blue light flickers every 4 

             

seconds alternately.

3.12 Passage Mode

Unlock the door with code, and press “*” before the motor turns back to the original place, buzzer gives a long “Di…”, blue 
light flickers every 4 seconds, the lock is under passage mode.

A

.

Unlock the door with fingerprint, and press “*” before the motor turns back to the original place, buzzer gives a long “Di…”, 
blue light flickers every 4 seconds, the lock is under passage mode. 

B

.

3.12.1 How to Set Passage Mode

Unlock the door with either fingerprint or code, the passage mode is canceled.

3. 12.2 How to Cancel Passage Mode

3.13 System Self-locked Function

When  enter  wrong  codes  continuously  for  10  times,  buzzer  gives  three  “Wu,  Wu,  Wu”  alarm,  red  light  flickers,  the  keypad  will  be 
locked for 5 minutes. At this time, keypad can be released by unlocking the door with valid fingerprint.

A

.

When input invalid fingerprint continuously for 10 times, buzzer gives three “Wu, Wu, Wu” alarm, red light flickers, fingerprint reader 
will be locked for 5 minutes. At this time, fingerprint reader can be released by unlocking the door with valid code.

B

.

If both keypad and fingerprint reader are locked by wrong operation, system will be locked for 5 minutes. After that, the system works 
again.

C

.

Turn mechanical key 72°

 

clockwise to set Passage Mode.

C

.

A

.

Turn mechanical key 55°counter

-

clockwise

 

to cancel Passage Mode.

B

.

3.14 

 

Low battery alarm and external power supply

When  the  sound  “do-re-mi-”  is  heard  during  opening  the  lock,  it  indicates  the  lock  in  low  battery  state.  The  lock  can  still  be 
opened  about  100  times  by  fingerprint  or  code  in  this  state.  Is  the  power  if  run  out  (neither  fingerprint  nor  code  can  open), 
external power supply or mechanical key can make open the lock. It is strongly recommended to replace battery when it is low. 

Chapter 3  Operations

Chapter 4 Maintenance

4.1. Battery Replacement

Insert a small tool into the Hole for opening Battery Box Cover (Fig1), 
press it and move upwards to open the cover (Fig2).

(

Fig1

)

(

Fig2

)

Tool

Hole for opening Battery Box Cover

Battery Box Cover

A

.

B

.

Chage

 

batteries

Summary of Contents for LIS2010-MT-1800/11

















Reviews: