Leuze electronic BPS 301i Original Operating Instructions Download

Page: 85 / 93

Ordering information and accessories

Leuze electronic

BPS 301i

Ordering information and accessories

14.1 BPS 301i type overview

Table 14.1:

BPS 301i type overview

14.2 Connection hoods

Table 14.2:

BPS connection hoods

14.3 Accessory terminating resistor

Table 14.3:

Accessories – terminating resistor

14.4 Cables accessories

Table 14.4:

Accessories – PWR connection cable (voltage supply)

Table 14.5:

Accessories – BUS IN connection cable (open cable end)

Part no.

Part designation

Description

50125671

BPS 301i SM 100 D H

BPS with RS 485 interface, display and heating

50125672

BPS 301i SM 100 D

BPS with RS 485 interface and display

50125673

BPS 301i SM 100

BPS with RS 485 interface

Part no.

Part designation

Description

50116469

MS 301

Connection hood with M12 connectors

50116464

MK 301

Connection hood with spring-cage terminals

50114571

KB 301-3000

Connection hood with cable

Part no.

Part designation

Description

50038539

TS 02-4-SA M12

M12 connector with integrated terminating resistor

for BUS OUT

Part no.

Part designation

Description

50104557

K-D M12A-5P-5m-PVC

PWR connection cable, M12 socket for PWR, axial

plug outlet, open cable end, cable length 5 m, not

shielded

50104559

K-D M12A-5P-10m-PVC

PWR connection cable, M12 socket for PWR, axial

plug outlet, open cable end, cable length 10 m, not

shielded

Part no.

Part designation

Description

M12 plug for BUS IN, axial connector, open line end

50104181

KB PB-2000-BA

BUS IN connection cable, length 2 m

50104180

KB PB-5000-BA

BUS IN connection cable, length 5 m

Summary of Contents for BPS 301i






























































































Search results

Summary of Contents for BPS 301i

Reviews:

Related manuals for BPS 301i

Brands by name

Popular brands

Leuze electronic BPS 301i, Original Operating Instructions

Search results

Summary of Contents for BPS 301i

Reviews:

Related manuals for BPS 301i

Brands by name

Popular brands