Let's Go Aero LittleGiant Assembly & Operating Instructions Download Page 15

Page 15 of 15

Maintenance Schedule

Below is a maintenance schedule for routine maintenance of your trailer.

 Warranty/Repair Procedures

Let’s Go Aero offers a 1 year limited warranty to each new Let’s Go Aero trailer against manufacturing defects in work-

manship and materials.
The obligation under this warranty is limited to the replacement or repair at the manufacturer’s factory, or at a point des-

ignated by the manufacturer, of such part as shall appear to the manufacturer upon inspection of such part to have been 

defective in material or workmanship. This warranty does not obligate Let’s Go Aero to bear the cost of labor or transpor-

tation charges in connection with the replacement or repair of defective parts, nor shall it apply to a product upon which 

alterations have been made or for equipment misused, neglected or improperly installed.
Let’s Go Aero reserves the right to improve any product through changes in design or materials as it may deem desirable 

without being obligated to incorporate such changes in products of previous manufacture.
Bills for service, labor, or other expenses which have been incurred by the buyer without express approval or authoriza-

tion by Let’s Go Aero will not be accepted.
If your trailer fails to operate properly, or fails within the warranty period, the following steps should be taken:

1.  An RMA is required for any return of product for warranty work of defective components. Contact Let’s Go Aero 

for an RMA, toll free 877-464-2376, toll 719-630-3800, or via email to [email protected]. Freight must be 

prepaid – collect shipments will be refused. Include your RMA number, name, return address, phone number and 

a description of the problem. A copy of the receipt including date of purchase is necessary for any warranty claim.

2.  If damages are due to abuse or misuse, owner will be charged for parts and labor.
3.  If any of the components of your trailer are found to be faulty due to defective material or workmanship, they will 

be repaired at no charge and returned with transportation charges prepaid. If failure occurred because of abuse, 

neglect or misuse, an estimate of cost to repair will be submitted back to the owner. After repairs are completed, 

the material will be returned with transportation charges collect.

Any modifications made to the trailer or parts of the trailer will void the trailer warranty and release Let’s Go Aero of any 

responsibility for damages, injuries or accidents incurred.
For further information and customer assistance, call toll free, 1-877-464-2376 or 719-630-3800.

Item

Function 

Required

500 Mile 

Intervals

3 Months

or

1000 Miles

6 Months

or

3000 Miles

12 Months

or

6000 Miles

Hub/Drum/Rotor

Bearings (Sure Lube-

Bearing Lube)

Seals

Wheel Lug Nuts & 

Bolts

Inspect for 

abnormal wear
Replenish grease 

in the system
Inspect for leakage 

replace is worn
Check torque 

valves

Summary of Contents for LittleGiant
















Reviews: