background image

Page 5 of 9

Using one (1) Wing 

[Z]

, slide both foam bumpers to the center of the Wing. 

Loosen handles on each Cradle Housing 

[AA]

. Slide two (2) Cradle Housings 

[AA]

 above the foam bumpers and two (2) Cradle Housings below the foam 

bumpers.

NOTE: 

The Knobs located on each Cradle Housing 

[AA] MUST

 rest along the 

same sides as the connection hole located at the bottom of the Wing. [Fg. 16]

NOTE:

 Position the Cradle Housing

 

so the Knobs alternate direction as shown.

Retighten each Cradle Housing

 

handle to secure in place on the Wing.  [Fg. 17]

Repeat this step for the second Wing. 

N

P

STEP 9

   

[Fg.15]

Never operate the carrier’s slide-out function without confirming the Safety Cable 

[R] 

is fully secured. Failure to 

follow proper procedures may result in bodily injury and property damage.

WARNING:

R

Attach the carabiner to the Safety Cable 

[R] 

(if not already pre-installed). 

From underneath the carrier, connect the quick-link end of the Safety Cable 

[R]

 to the hole in the frame of the TwinTube 

[A]

. [Fg.15]

NOTE: 

The Safety Cable 

[R]

 can be secured in two positions. Secure the 

Safety Cable to the first position. For maximum installed clearance needs, 

the second position may be used.

With the Hat Brackets 

[P]

 from STEP 5 & 6 still loosely secured, adjust the 

Base 

[N]

 back and forth along the Slide Tubes 

[M]

 to adjust for required 

user application and vehicle clearances.

 Tighten the bolts on the Hat 

Brackets [P] firmly once determined.

IMPORTANT: 

The Base 

[N] 

must be positioned forward of the Handle 

Silent Hitch Pin location (close to vehicle). Be sure to allow room for the Pin 

handle to turn and operte as required.

A

DO NOT ALLOW HAT BRACKETS [P] TO OVERLAP THE WARNING LABEL LOCATED ON 

THE SLIDE TUBE.

 Failure to do so may permit over-extension of the Safety Cable allowing the 

Slide Tubes to come off and cause damage or personal injury. 

      WARNING:

 

Z

AA

AA

AA

 

STEP 10: 

HANDLE

KNOB

KNOB

FOAM 

BUMPERS

2ND POSITION

1ST POSITION

CONNECTION 

HOLE

[Fg. 17]

[Fg. 16]

Summary of Contents for B02158










Reviews: