background image

Operating Instructions

1

01334J

12 VOLT FULLY AUTOMATIC

BATTERY CHARGER

MODEL 15840

Specifications

AC Supply:

100-125 or 200-250 volts, 50 or 60 Hertz, single-phase

DC Output:

12 volts, 10 amps, tapering to 3 amps or less

Battery Capacity:

Use only on 12 volt, 6 cell, 55 to 105 ampere-hour (20 hr. rate) liquid electrolyte lead
acid batteries

PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS

For correct operation of the equipment, it is important to read and be familiar

with this entire manual before installing and operating the charger.

DO NOT DISCARD THIS MANUAL AFTER READING.

LOOK  FOR  THIS  SYMBOL  TO  POINT  OUT  SAFETY  PRECAUTIONS.    IT  MEANS:

BECOME  ALERT—YOUR  SAFETY  IS  INVOLVED.

IF  YOU  DO  NOT  FOLLOW  THESE

SAFETY INSTRUCTIONS, INJURY OR PROPERTY DAMAGE CAN OCCUR.

IMPORTANT SAFETY INSTRUCTIONS

1.

This  manual  contains  important  safety  and
operating  instructions.    Read  and  understand
this  entire  manual  before  installing  or  operating
the charger.

2.

Before 

using 

battery 

charger, 

read 

all

instructions  and  cautionary  markings  on  battery
charger, battery, and product using battery.

CAUTION:    TO  REDUCE  RISK  OF  INJURY,

CHARGE  ONLY  LIQUID  ELECTROLYTE  LEAD
ACID  RECHARGEABLE  BATTERIES.    OTHER
TYPES  OF  BATTERIES  MAY  BURST  CAUSING
PERSONAL INJURY AND DAMAGE.

3.

Do not expose charger to rain or snow.

4.

Use of an attachment not recommended or sold
by  the  battery  charger  manufacturer  may  result
in  a  risk  of  fire,  electric  shock,  or  injury  to
persons.

5.

To  reduce  risk  of  damage  to  electric  plug  and
cord,  pull  by  plug  rather  than  cord  when
disconnecting charger.

6.

Make  sure  cord  is  located  so  that  it  will  not  be
stepped on, tripped over, or otherwise subjected
to damage or stress.

7.

An  extension  cord  should  not  be  used  unless
absolutely  necessary.    Use  of  improper
extension  cord  could  result  in  a  risk  of  fire  and
electric  shock.    If  extension  cord  must  be  used,
make sure that:

a.

Pins on plug of extension cord are the same
number, size, and shape as those of plug on
charger cord.

b.

Extension cord is properly wired and in good
electrical condition.

c.

Wire  size  is  large  enough  for  AC  ampere
rating of charger.

Summary of Contents for 15840






Reviews: