Leonton ET2-1600 Series User Manual Download Page 7

Package Contents 

 

1 - ET2-1600(-T) 

0.628 kg (1.38 lb), Shipping weight: 0.812 kg (1.79 lb)

 

 

2 - Wall mounting brackets and screws 

 

 

1 - Quick installation guide 

 

 

Safety Precaution 

Attention

 

If the DC voltage is supplied by an external circuit, please use a protection device on the power 

supply input. Supply by UL Listed industrial use power. The industrial Ethernet switch’s hardware 

specs, ports, cabling information, and wiring installation will be described within this user manual. 
 

Attention

 

Si la tension CC est fournie par un circuit externe, veuillez utiliser un dispositif de protection sur 
l'entrée  d'alimentation.  Fourniture  par  courant  industriel  homologué  UL.  Les  spécifications 
matérielles, les ports, les informations de câblage et l'installation du câblage du convertisseur de 
média industriel seront décrits dans ce manuel d'utilisation. 

 

Warning Labels 

The  caution  label  means  that  you  should  check  the  certain  information  on  user  manual  when 
working with the device. (Shown in 

Figure 1.1

 

Étiquettes d'avertissement 

L'étiquette d'avertissement signifie que vous devez vérifier certaines informations sur le manuel 
d'utilisation lorsque vous travaillez avec l'appareil. (Montré dans la 

Figure 1.2

 

Figure 1.1 - Caution Label 

Figure 1.1 - Étiquette de mise en garde 

 

Figure 1.2 - Hot Surface Warning Label 

Figure 1.2 - Étiquette d'avertissement de surface chaude 

Summary of Contents for ET2-1600 Series




















Reviews: