Lenze PROFINET 9400 Communications Manual Download Page 108

Page: 108 / 119

Parameter reference

14.3

Parameters of the communication module for slot MXI2

108

Lenze · E94AYCER communication module (PROFINET®) · Communication Manual · DMS 11.0 EN · 04/2016 · TD17

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

C14879

C14880

C14881

C14882

Parameter | Name:

C14879 | Bus error

Data type: UNSIGNED_32

Index: 9696 = 0x25E0

Display of the error currently detected on the fieldbus.

Display range

(min. value | unit | max. value)

4294967295



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Value

Meaning

No error

3481402629

The PROFINET communication link has been interrupted.

Parameter | Name:

C14880 | Reaction on communication fault

Data type: UNSIGNED_8

Index: 9695 = 0x25DF

The action set in subcode 1 is executed when the node detects that it is no longer in the "Data_Exchange" state.

• Please also observe the notes provided in code

C14881

• A change in the monitoring response becomes immediately effective.



Interruption of PROFINET communication (



77)

Selection list

0 No response
1 Fault
3 Quick stop by trouble
4 Warning Locked
6 Information

Subcodes

Lenze setting

Info

C14880/1

0: No Response



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Parameter | Name:

C14881 | Response time when exiting "Data_Exchange"

Data type: UNSIGNED_16

Index: 9694 = 0x25DE

If the "Data_Exchange" status is exited, the response parameterised in

C14880

is activated after the time set here

has expired.

• A value of "65535" in this code deactivates the monitoring function.

• A change in the monitoring response becomes immediately effective.

Setting range

(min. value | unit | max. value)

Lenze setting

65535

0 ms



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Parameter | Name:

C14882 | Display: Monit. time: Watchdog

Data type: UNSIGNED_32

Index: 9693 = 0x25DD

Display of the watchdog monitoring time specified by the IO controller

Note:

This code will not be supported anymore

from SW version 2.10

for reasons related to the system.

Display range

(min. value | unit | max. value)

4294967295



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Summary of Contents for PROFINET 9400
























































































































Search results

Summary of Contents for PROFINET 9400

Reviews:

Related manuals for PROFINET 9400

Brands by name

Popular brands

Lenze PROFINET 9400, Communications Manual

Search results

Summary of Contents for PROFINET 9400

Reviews:

Related manuals for PROFINET 9400

Brands by name

Popular brands