Lenze POWERLINK E84DGDV Series Communications Manual Download Page 48

Page: 48 / 70

Parameter reference

Parameters relevant for POWERLINK communication

Lenze · Decentralised frequency inverter 8400 motec (POWERLINK Option) · EDS84DMOTPL EN 1.0 - 11/2018

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

C13028

The describing bit field has the following structure:

Parameter | Name:

C13028 | 0x1F81 Node Assignment CN

Data type: UNSIGNED_32

Index: 11547

= 2D1B

The code declares the controlled nodes 1 ... 100 and their properties.

Value is bit-coded:

Bit 0 ... 31 see below

Subcodes

Lenze setting

Info

C13028/1

...

C13028/100



Read access



Write access



CINH



PLC-STOP



No transfer



PDO_MAP_RX



PDO_MAP_TX



COM



MOT

Bit

Value

Description

0 (LSB)

EPL node with this ID does not exist.

EPL node with this ID exists.

EPL node with this ID is not a controlled node.

EPL node with this ID is a controlled node.

On detection of a booting controlled node, the application will not be informed.

On detection of a booting controlled node, the application will be informed and the

controlled node will be started.

Optional controlled node

Obligatory controlled node

The managing node is allowed to send reset commands.

The managing node must not send any reset command.

Software version verification of the controlled node is not required.

Software version verification of the controlled node is required.

Automatic application software update is not allowed.

Automatic application software update is allowed.

Reserved / No function

Isochronously accessed controlled node

Asynchronously accessed controlled node (bit 9 is irrelevant)

Continuously accessed controlled node

Multiplex EPL nodes are supported.

No "POWERLINK to standard Ethernet" router function.

The device can be used as an "POWERLINK to standard Ethernet" router (router type 1).

No "POWERLINK to fieldbus" router function.

The device can be used as an "POWERLINK to fieldbus" router (router type 1).

The managing node does not send any PRes frames

The managing node sends PRes frames

13 ... 30

Reserved / No function

31 (MSB) 0

Bits 0 ... 30 inhibited

Bits 0 ... 30 enabled

Summary of Contents for POWERLINK E84DGDV Series







































































Search results

Summary of Contents for POWERLINK E84DGDV Series

Reviews:

Related manuals for POWERLINK E84DGDV Series

Brands by name

Popular brands

Lenze POWERLINK E84DGDV Series, Communications Manual

Search results

Summary of Contents for POWERLINK E84DGDV Series

Reviews:

Related manuals for POWERLINK E84DGDV Series

Brands by name

Popular brands