Lenze E84AYCEC Communications Manual Download Page 53

Page: 53 / 90

Lenze · E84AYCEC communication module (POWERLINK) · EDS84AYCEC EN 4.0 - 02/2019

Diagnostics

LED status displays

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

9.1.1

Module status displays

The LEDs

ME, BE

and

indicate the module status.

E84YCEC003A

odule

tatus

odule

rror

evice

rror

LED

Colour

Status

Description

green

The communication module is supplied with voltage and is connec-

ted to the standard device.

blinking

The communication module is supplied with voltage, but has no con-

nection to the standard device. (The standard device is either swit-

ched off, in the initialisation phase, or not available).

red

An error has occurred in the communication module.

red

A fieldbus error has occurred.

red

The communication module is not accepted by the standard device.

See notes given in the documentation for the standard device.

Summary of Contents for E84AYCEC



























































































Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands

Lenze E84AYCEC, Communications Manual

Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands