Lenze E84AYCEC Communications Manual Download Page 29

Page: 29 / 90

Lenze · E84AYCEC communication module (POWERLINK) · EDS84AYCEC EN 4.0 - 02/2019

Installation

Electrical installation

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

5.2.4

Basic Ethernet Mode

The communication module can be operated in the "Basic Ethernet Mode" for a basic parameter set-

ting provided that the following applies:

1. Operation of the module with network address

≤

239.

• IP address: 192.168.100.[

EPL address

]

• see

2. No operation with real-time EPL must be carried out.
3. No integration of a managing node (EPL address

240) into the standard Ethernet network.



Note!

Operation in the "Basic Ethernet Mode" does not permit any real-time communication.

Summary of Contents for E84AYCEC



























































































Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands

Lenze E84AYCEC, Communications Manual

Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands