Lenze E84AYCEC Communications Manual Download Page 37

Page: 37 / 90

Lenze · E84AYCEC communication module (POWERLINK) · EDS84AYCEC EN 4.0 - 02/2019

Commissioning

Node address setting

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

6.2

Node address setting

The node address is set via the two front panel rotary coding switches "Node ID".

[6-1]

Rotary coding switches "Node ID"

• The labelling of the rotary coding switches corresponds to the values for determining the node

address.

• Valid addresses for the communication module in the EPL network:

• 1 … 100: Controlled node with Lenze module E94AYCEP as managing node
• 1 … 239: Controlled node with managing node of another manufacturer

• The corresponding Ethernet IP address of the communication module results from the address

setting of the rotary coding switches:

• IP address: 192.168.100.[

EPL address

]



Note!

• Each network node address must only be used once.
• The node address setting in the configuration software (e.g. »Engineer«) and the ro-

tary encoder switches must be identical for each node.

• Adjustable address range: 1 ... 239
• Switch the voltage supply of the communication module off and on again to activate

changed settings.

Symbol_NodeID

Summary of Contents for E84AYCEC



























































































Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands

Lenze E84AYCEC, Communications Manual

Search results

Summary of Contents for E84AYCEC

Reviews:

Related manuals for E84AYCEC

Brands by name

Popular brands