manualshive.com logo in svg

Lenze AC Tech LonWorks MCH Series, Communications Manual

Share
Download
Lenze AC Tech LonWorks MCH Series Communications Manual Download Page 25

RG-MHLON 

22

LonWorks Network Variables

nciStopMode

Definition 

Network config input SNVT_switch nciStopMode

Explanation 

This input network variable is used to choose between coast and ramp stop.

Valid Range:

State

Value

Command

0

0.0%

Coast to stop

1

100.0%

Ramp to stop

Default Value  0

nciStopLevel

Definition 

Network config input SNVT_lev_percent nciStopLevel

Explanation 

This is the stop level for the drive when it is in ramp to stop mode. When the drive 
is ramping to a stop and reaches this level, a coast to stop is performed. The value 
is relative to nvoDrvSpeed ( i.e. a value of 5% corresponds to a nvoDrvSpeed value 
of 5%).

Valid Range 

-163.840% to 0.00 % or 0.00% to +163.835%

 

The value 0x7FFF represents invalid data.

Default Value  5.000 %

nciParValue

Definition 

Network config input SNVT_count_inc nciParValue

Explanation 

This nci is used as a value input for the user selected parameter nciParWrite.

Valid Range 

1 - 46

Default Value  0

nciParRead

Definition 

Network config input SNVT_count nciParRead

Explanation 

Chooses the parameter value to be read from the drive.

Valid Range 

1 - 46

Default Value  0

Summary of Contents for LonWorks MCH Series




























Reviews:

No comments

Brands by name

Popular brands

Load more brands