Lenovo ThinkCentre M90t Gen 3 Hardware Maintenance Manual Download Page 81 | Manualshive

Page: 81 / 104

Lenovo ThinkCentre M90t Gen 3 Hardware Maintenance Manual Download Page 81

2. Position the new heat sink and fan assembly on the system board. Ensure that the four screws are

aligned with the holes in the system board. Follow the following sequence to tighten the four screws to
secure the new heat sink and fan assembly to the system board. Do not over-tighten the screws. Then,
install the four screws to secure the new heat sink and fan assembly to the chassis.

• Partially tighten screw

2a

, fully tighten screw

2b

, and then fully tighten screw

2a

.

• Partially tighten screw

2c

, fully tighten screw

2d

, and then fully tighten screw

2c

.

Notes:

• Apply appropriate amount of thermal grease to the new heat sink and fan assembly.

• Ensure that the heat sink and fan assembly cable is toward the microprocessor fan connector on the

system board.

• In case you need to install the chassis beam as well, ensure that it has been installed in place before

you install 125-watt heat sink and fan assembly.

Hardware removal and installation

75

«
...
79
80
81
82
83
...
»

Summary of Contents for ThinkCentre M90t Gen 3









































































































Reviews:

No comments