manualshive.com logo in svg

Lenovo ThinkCentre M90t Gen 3, Hardware Maintenance Manual, Page: 42 / 104

Share
Download
Lenovo ThinkCentre M90t Gen 3 Hardware Maintenance Manual Download Page 42

Message/Symptom

FRU/Action

Power-on indicator or hard disk drive in-use light not on, 
but computer works correctly

1.  Power switch/LED assembly

2.  System Board

Printer problems

1.  Printer

2.  System Board

Program loads from the hard disk with a known-good 
diagnostics diskette in the first 3.5-inch diskette drive

1.  Run the Setup Utility program and check the Startup 

sequence.

2.  Diskette Drive

3.  Diskette Drive Cable

4.  System Board

5.  Power Supply

RPL computer cannot access programs from its own hard 
disk.

1.  If the network administrator is using LCCM Hybrid 

RPL, check the startup sequence: 

a. 

First device - network

b. 

Second device - hard disk

2.  Hard disk drive

RPL computer does not RPL from server

1.  Check the startup sequence.

2.  Check the network adapter LED status.

Serial or parallel connector device failure (system board 
connector)

1.  External Device Self-Test OK?

2.  External Device

3.  Cable

4.  System Board

Serial or parallel connector device failure (adapter 
connector)

1.  External Device Self-Test OK?

2.  External Device

3.  Cable

4.  Alternate Adapter

5.  System Board

Some or all keys on the keyboard do not work

1.  Keyboard

2.  Keyboard Cable

3.  System Board

Undetermined problems

This section provides instructions on how to find out the failing devices or adapters. 

1.  Turn off the computer.

2.  Remove or disconnect the following components (if installed) one at a time.  

a.  External devices (modem, printer, or mouse)

b.  Any adapters

c.  Memory modules

d.  Extended video memory

36

M90t Gen 3 Hardware Maintenance Manual

Summary of Contents for ThinkCentre M90t Gen 3









































































































Reviews:

No comments