manualshive.com logo in svg

Lenovo ThinkCentre M90t Gen 3, Hardware Maintenance Manual, Page: 102 / 104

Share
Download
Lenovo ThinkCentre M90t Gen 3 Hardware Maintenance Manual Download Page 102

Any performance data contained herein was determined in a controlled environment. Therefore, the result 
obtained in other operating environments may vary significantly. Some measurements may have been made 
on development-level systems and there is no guarantee that these measurements will be the same on 
generally available systems. Furthermore, some measurements may have been estimated through 
extrapolation. Actual results may vary. Users of this document should verify the applicable data for their 
specific environment.

This document is copyrighted by Lenovo and is not covered by any open source license, including any Linux 
agreement(s) which may accompany software included with this product. Lenovo may update this document 
at any time without notice.

For the latest information or any questions or comments, contact or visit the Lenovo Web site: 

https://pcsupport.lenovo.com

Trademarks

LENOVO, LENOVO logo, THINKCENTRE, and THINKCENTRE logo are trademarks of Lenovo. Intel and 
Thunderbolt are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries. 
Microsoft, Windows, and Cortana are trademarks of the Microsoft group of companies. DisplayPort is a 
trademark of the Video Electronics Standards Association. The terms HDMI and HDMI High-Definition 
Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States 
and other countries. Wi-Fi and Miracast are registered trademarks of Wi-Fi Alliance. USB-C is a registered 
trademark of USB Implementers Forum. All other trademarks are the property of their respective owners.

96

M90t Gen 3 Hardware Maintenance Manual

Summary of Contents for ThinkCentre M90t Gen 3









































































































Reviews:

No comments