manualshive.com logo in svg

Lenovo ThinkCentre 0401, Hardware Maintenance Manual, Page: 75 / 170

Share
Download
Lenovo ThinkCentre 0401 Hardware Maintenance Manual Download Page 75

Diagnostic Error Code

FRU/Action

215-000-XXX

CD-ROM Drive Test Passed

No action

215-XXX-XXX

CD-ROM Drive error

1.

CD-ROM Drive Cable

2.

Check power supply voltages

3.

CD-ROM drive

4.

System board

217-000-XXX

Hard Disk Drive Test Passed

No action

217-25X-XXX
217-26X-XXX

Hard Disk Drive (IDE) error

1.

Hard Disk Drive Cable

2.

Check power supply voltages

3.

Reseat the hard disk drive cable

4.

Hard Disk drive (IDE)

5.

System board

217-28X-XXX
217-29X-XXX

Hard Disk Drive (SCSI) error

1.

Hard Disk Drive Cable

2.

Check power supply voltages

3.

Reseat the hard disk drive cable

4.

Hard Disk drive (SCSI)

5.

SCSI adapter card

6.

System board

220-000-XXX

Hi-Capacity Cartridge Drive Test Passed

No action

220-XXX-XXX

Hi-Capacity Cartridge Drive error

1.

Remove the Hi-Capacity Cartridge
Drive and re-test the system

301-XXX-XXX

Keyboard error

1.

Keyboard

2.

Check and test mouse

3.

System board

301-000-XXX

Keyboard Test Passed

No action

302-000-XXX

Mouse Test Passed

No action

302-XXX-XXX

Mouse error

1.

Mouse

2.

Check and test Keyboard

3.

System board

303-000-XXX

Joystick Test Passed

No action

303-XXX-XXX

Joystick error

Remove the Joystick and re-test the system

305-000-XXX

Monitor DDC Test Passed

No action

305-250-XXX

Monitor DDC self test failure

1.

Run Setup to enable DDC

2.

Cable

3.

Monitor

4.

Video card

5.

System board

Chapter 7. Symptom-to-FRU Index

69

Summary of Contents for ThinkCentre 0401











































































































































































Reviews:

No comments